Eline-technology SNI-CamSetup Instrukcja Użytkownika Strona 1

Setup User’s Manual

9

1. Network type: specify the IP address. 11 Manual port mapping, you can not enable automatic port ma

If the user chooses to automatically obtain an IP address. Generally do not need to fill in the other parameters. "Use the following DNS server a

The first use of wireless camera, the first camera to plug the Internet cable, find the camera setup camera list, select the view, and do the followi

15 16

17 18 The wir

<5> Account (Account ID) and password (Password) Registered account can facilitate the management and authorization. An account can manage mu

21 eLine Sniper Camera Setup ManualeLineTec

3. Log in Register page New User Registration Shown in Figure 21, click on the registered account into the account registration page

4. Management Center After successful registratio

第 - 19 - 页 共 44 页 1． Add equipment: (1) Add the camera. N

27 The user can set the subsidiary user permi

第 - 21 - 页 共 44 页 1． Sub-account settings: the need to

28 （2）Sub-account information in the sub-account under the management of the Central Administration interface column view, click on th

<6> Video Preview 30 <7> Lens control Divided into several states: According to different models of camera

32 Video Set Camera Model 2C Environment Mode：User can set camera’s environment to get a better image quality. “

Advanced Camera Model 2C 1. auto white balance：This option is preferred. 2. config white balance：Adjust balance between Green, Red, and Blue. 3.

The camera Model 8 series 1.HZ: you can select the frequency of this corresponds to remove the video water wave phenomena. 2.color hue: You can ad

Video settings Camera Model F/G 1.HZ: you can select this corresponding frequency to remove the video water wave phenomena. 2.WDR: Set the video wi

Scene set Camera Model F/G Select the white balance mode is set accordingly. eLine Sniper Camera Setup ManualeLineTechnology.com28

SETUP TABLE OF CONTENTS ... - 1 -

Extended settings Camera Model F/G 1. Adjustment for video brightness. 2. Adjust contrast. 3. Adjust hue. 4. Adjust saturation. 5. : a

<8> PTZ Control When the selected camera PTZ function, PTZ control can be hired, otherwise it will grayed out. Click "PTZ Control PTZ

33 Cruise program settings: set a total of nine cr

<9> Video settings <9.1> SD card recording - only for the camera with SD card recording function Click "SD card recording, the us

35 图 36 37 Recording schedu

38 Motion detection settings (alarm settings): Check e-mail alerts when motion is detected, the pr

39 40 &l

41 42 Config NAS Enabled NAS: select this option will be based o

<10> Video Download Click "Video Download, you can download SD card recording to the local. Video download page click on the "dow

45

If you only use the LAN, you do not need to do special network settings, is a "plug and play" hardware. As used in the Internet (Inte

47

<12> Remote playback Remote video playback is viewed through the web to achieve. To achieve remote viewing and playback, you must register the a

51 （2）Other features and controls The user c

53 3. The plug-in above the control bar.

<13> Troubleshooting Q1: the network cable and the power cord is plugged in, but the LAN can not see images? A1: The network camera does not nee

Refer to the following diagram to connect the way, depending on the settings of the local area network, online network camera is set to DHCP to auto

<2> Install application software <2.1> Setting interface (Setup software) Click on the right side of the middle run Setup "to enter

 Dserver:The address of the server registered by the registration server cameras are watching。 3. LAN monitoring "Camera Name" list, dou

<3> System Tools 6 <3.1> Mode is set

<3.2> Allowed to enter the IP address directly access the camera 8 <4